Grey Paint Brush

Painting tips from me will be about as basic as it gets, I'm no expert. Surface prep is where the average paint job fails to look as good or last as long as it should. Painting over dirt and loose paint is just wrong. Every bit of time spent (scraping, sanding, cleaning) is time well spent. There may still be times when there is a little paint left in the gun after spraying some parts. In that case, doing a quick dust-off and respray of some running boards, or pedals on another tractor is better than dumping the extra paint on the ground. The photo above shows two extremes. Lots of time and effort was spent on the sheetmetal, but the transmission and rear castings were just a quick spray-over.

  • Richeson Grey Matters Pocket Brushes feature non-reflective hair, non-reflective ferrules, and non-reflective handles — perfect for plein air or in the studio, and ideal for use with watercolors. Closed length is approximately 3-5/8' - 4-5/8'.
  • Gray continues to top the list of popular paint colors for homeowners, and for a good reason. Whether cool, warm, light, or bold, grays of all tones and intensities provide a fresh backdrop for decor and coordinate beautifully with tile, countertops, furnishings, and art. Although this crisp neutral is highly versatile, gray is one of the most challenging colors to select due to its shifting.
  • Product description Innovative Grey Matters brushes reduce any distraction a painter may have with light or color mixing. The bristles, ferrule and handle are all non-reflective and the neural grey bristles minimize color distortion. This set of 6 Short-handle Synthetic Watercolor Brushes contains shapes and sizes designed to work together.
  • Rust-Oleum 32 oz. Kensington Gray Milk Paint provides a quick and easy way to paint your new or old, vintage furniture and decor. One-step, buildable paint finish makes upcycling a breeze in an environmentally friendly formula with low odor and low VOC.

If you want a show-quality finish, there is no substitute for stripping everything to metal. If all you want is a better looking tractor, stripping everything to bare metal is not necessary. Seal all openings. Remove or cover the carb, distributor, and electrical parts and give the tractor a good power-washing. You will need some scrapers and wire brushes to help remove caked-on gunk. Power Washing is not the preferred method of cleaning your tractor on a regular basis. Frequent power washing will thoroughly screw up carburetors, distributors, air cleaners, gauges, and electrical components. Painting requires removal of all dirt and grease so power washing may be the best way to remove most of the stuff that collects on any tractor. The spray nozzle will also blast away any loose paint.

One of over 3,500 exclusive Benjamin Moore colors. On-screen and printer color representations may vary from actual paint colors.

The tractor will soon look a lot better, but there will still be dirt and loose paint. Use whatever is handy and seems appropriate to get into the nooks and crannies. Small picks scrapers and stiff brushes will turn up a lot of areas that need additional attention. Sand any old paint drips or sags. Sand edges of chipped areas to blend with adjacent surface. If chipped areas continue to flake-off, the old paint is loose and needs to come off. Keep scraping and sanding until the finish is smooth to touch. Now is the time to do any body-work or cast iron repairs. It is possible to braise or weld cast iron. You can even use liquid metal epoxy for some repairs.

Now is the time to decide how much time will be spent on bodywork. It takes little effort to make the cast iron parts look good. Sheet metal parts are a lot more difficult to finish well. Some people can feel if a panel is smooth, others like to spray a quick coat of primer to see if more work is necessary. It is generally easier to finish small parts and all sheetmetal parts separately. Disassembly may be easier than trying to mask everything. Different color parts finished separately always look much better than any masking job. Sheetmetal can even be taken to a body shop if the damage appears to be more than you want to deal with.

Refinishing small parts such as carb castings, headlights, brackets, linkage, etc. can be time-consuming. Prepping for paint, waiting for primer to dry, then waiting for finish coats to dry might significantly delay being able to reassemble those parts. Powder-coating is one way to refinish parts that required almost no drying time. As soon as the parts are cool enough to touch, they are ready to be reassembled.


Many years ago Eastwood ran a sale on their entry-level HotCoat Powder Gun and Starter Kit. Their gun requires compressed-air and a standard electrical outlet to run. No problem. We bought a new toaster-Oven for the kitchen so I could have the old one to use out in the shop for powder-coating. The Eastwood Gun worked well and their powder paint is superior to any other brand that I've tried. The Eastwood powders just seem to apply better with fewer problems. Steam gtfo game.

Powder-Coating does require stripping parts to bare metal. That takes some time, but not nearly as much as waiting for primer and paint to dry. It is best to pre-heat parts for a few minutes to bake out any moisture or oil that may still be present after normal prep. Powder sticks better to warm parts. Wear gloves and do not touch parts with bare hands before applying powder. Pull the part(s) out of the oven, and wipe down with a clean rag. Find a way to move coated parts into the oven without knocking the powder off. Some parts can sit on a metal grate or tray. Other parts can be handled better with wire hooks. Anything used to coat and place parts in the oven will also become powder-coated.

Powder contains hardeners that can irritate skin and certainly should not be sucked into your lungs. Health concerns are similar to many of the chemicals and dust we create in the shop. A large cardboard box makes a pretty good 3-sided spray 'booth' that makes cleanup a lot easier and can allow some powder to be salvaged. The Eastwood gun worked ok until a different style turned up on clearance at Sears. This identical powder gun has been sold by several companies. Eastwood may even have sold them for a short time. They are very cheaply made and easily broken, but if treated carefully they will last many years. I've never paid more than $25. These guns use an internal fan rather than an air compressor. One tiny wire from the transformer means the gun is a lot easier to use and simply works better than many more expensive guns.

The absolute best thing about powder-coating is after 20 minutes in the oven it's completely DONE. Open the door and it takes very few minutes for the parts to cool enough to handle. The coating is tough and seems to be more fuel resistant than any paint. Color choices were good enough to match up a good Ford Red, a gray, black, and I've tried several chrome finishes. Powder colors can be mixed but the results can be strange if not thoroughly mixed. Powder-coated lug nuts turned-out well and durable enough using a 6-point socket. Powder does add thickness, so a heavy application on nuts and bolts could make it difficult to fit the correct socket or wrench on them.


Chrome Plating is usually way beyond my budget and is not a process anyone should be doing at home. Chrome plating is very cool. . Ceramic coating may be the best possible finish for exhaust manifolds and head pipes. It isn't 'plating' but it's another process that the parts need to be sent off to have done. Tin-Zinc plating is something that can be done at home. Zinc plating requires and acid solution so it isn't something you want splashed or spilled. Some of the parts placed in my electrolysis tank over the years have emerged with a bit of copper plating. If the copper clamp to the sacrificial metal falls into the tank, it becomes the sacrifice and some of the copper did appear as a light plating on the part I was cleaning. This gave me the idea to look into zinc plating. The process is similar to electrolysis. Eastwood sells a small tin-zinc plating kit that works really well to restore some of the special nuts and bolts on these tractors. Unlike electrolysis, the tin-zinc process uses an electrolyte solution that contains Sulphuric Acid. The parts come out with a grey coating that can be polished to look like new shiny zinc hardware. Unfortunately, the coating does not seem to last as long as new hardware. Tin-Zinc plating is still a good option for hardware tha cannot be easily replaced.

Unpainted Items

Nothing spells 'amateur' better than overspray on tires, or painted wiring and rubber parts. Things that should remain unpainted should be carefully masked or removed. There are several spray-on products that make tires look like new. In fact, a little dish detergent and water scrubbed on tires does as well as many of the sprays, costs less, but is more work. I accidentally discovered that the lanolin hand cleaner works better than anything else to restore smaller rubber things like plug wires and shift boots. The Ford 3000 pictured above came with hard plastic shift knobs and steering wheel cap. Rather than try to make those look good, I turned new ones from billet aluminum on my lathe, then polished them till they look like chrome.

PAINTING - with Air Compressor, Rattle Cans, or Brush

Many very nice paint jobs have been done with rattle cans or even a brush. Using a spray gun does not guarantee a better job. If you already have an air compressor, a spray gun is a good investment. One quart can of paint, applied with a spray gun, will cover as much as about 12 rattle cans. Painting with a brush takes much longer and generally uses a lot more paint than spraying. For small parts and small jobs, it's hard to beat the convenience of rattle cans.

Sadly, my long time exclusive preference for Rustoleum 'Stops Rust' spray paint has ended. Rustoleum was always my first choice for metal, and always gave good results. Unfortunately, when they redesigned the nozzles away from the universal tiny male spray heads, the Rustoleum spray cans no longer work for me. Paint or primer, the new cans just spatter, sputter, drip, and clog. The nozzle can be cleaned, but then every single Rustoleum spray can clogs internally with 25 to 50 percent of the paint still in the can. After collecting a dozen or so partially full cans that will no-longer squirt, I got tired of wasting money and started buying Krylon spray cans. Over the last two years I've not had a single Krylon paint or primer spray can fail to work as it should.

Final Prep. and Primer

No matter how you plan to apply the finish coats, always use a good primer that is compatible with the paint you are going to use. Paint applied to bare metal without primer will soon start to bubble chip, and peel. Spend some time making sure the surfaces are clean, smooth, primed, and ready for paint. This is the step that has the most effect on the quality of the finish. Start with one light coat of primer. Then carefully inspect the appearance. How good did you do on the bodywork? Small imperfections can be filled with primer by spot-painting them and lightly-sanding until the primer fills the low spot. Tractor sheet metal is plenty thick enough for traditional hammer and dolly work. Some folks will use a skim coat of bondo and then sand the panel, leaving bondo only in the low spots. I believe that is going way too far for a working tractor. I'm happy if the panels are mostly straight. A few small dents add character, grin. Once you are satisfied with the bodywork, shoot one light coat of primer on everything. Let it dry thoroughly, then sand with fine (180-220) grit paper, or use clean steel wool. Finally, just before spraying the first finish color, go over the surface with a clean rag and mineral spirits to remove any dust or oils. A single oily finger print can mess-up the finish. If you are painting in the great outdoors, try to pick a day with low winds, not too much sun, and few bugs. Good luck with that. When I'm ready to paint I paint. My 8N is nicknamed 'BUGS' for all the gnats in the paint.

Finish Painting

If using an air compressor and spray gun, one quart of primer and one quart of each color is enough to do the 8N red-belly paint scheme with two coats of the finish colors. If you want more coats or shoot much thicker coats, get two quarts of each color. For most working tractor paint jos, my advice is to skip hardeners and other paint additives. Paint fumes are bad enough without adding more toxic substances. Few home shops have the proper booth, clothing, respirators, and other equipment required to shoot paint with additives. That stuff can kill you D-E-D dead, or make you wish you were dead. Get the material safety data sheets for any paint additives you think you want to use. Just do a web search for the product and add MSDS to the search. If you become sensitized to some of these products, it may put you in the hospital and cause permanent health issues. It just isn't worth the risk for a one-shot deal on a working tractor. Leave additives to the folks painting show cars who have the proper safety equipment. Finally, the benefits provided by additives are completely wasted on a working tractor. A good quality enamel will last at least 10 years and still clean up well (if you ever bother to wash the dirt off your working tractor). It's been well over ten years since I painted my 8N and 2N. None of the warts they have collected over the years would have been prevented by adding hardener to the paint. Hardener will not prevent paint from wearing off pedals and footboards.

With most paint guns the paint must be thinned for spraying. My spray gun seems to like thinning with 5% mineral spirits (that works out to adding 1.6 ounces of mineral spirits to one quart can of paint). There is enough room in the quart paint can to add the thinner, put the lid back on, and shake it up. Information about thinning and spray tip size should be printed on the paint can. The newer HVLP spray guns create a lot less overspray than the older type of equipment that I use. If you adjust the HVLP gun correctly, you should be able to get good coverage with a lot less overspray. You still need a mask to keep overspray out of your lungs. For a one-time deal, painting ooutside, with good ventilation, the disposable masks work ok, the ones with filters work better.

Clear Coat

A cheap clear paint will turn yellow, crack, flake, and generally look ugly much faster than plain enamel and decent quality vinyl decals will last without clear coat. Good quality vinyl or water-transfer type decals last about the same time as paint for me (5-10 years). There are different grades of vinyl and some inks are more UV resistant than others. Cheap vinyl decals will soon start to curl at the edges, and quickly fade.

After experimenting with several clear coat products, most have created more problems than they fixed. In theory, a good clear coat should provide additional UV protection, provide a deeper shine, and stay shiny much longer. This works really well for modern automotive base coat, clear coat finishes. It is very difficult to do a good base coat, clear coat finish in the typical garage/barnyard. The better clear coat products cost at least $20 to $25 for one rattle can, and about $30 for a quart. Adding clear coat more than doubles the cost of just spraying enamel. Some of my clearcoat projects have turned out great, and were worth the effort/expense. Some have been a complete failure.


Some purists may whine about green and yellow Fords or 9N tractors painted with the Red-Belly paint scheme. Tough, this is your tractor, so feel free to paint it any colors you choose. I believe the best value is to stay with original colors. Any future restorer is going to strip whatever paint is there and start over. No-matter what color you use any paint will protect the metal.

One story going around is that Barn Sparrows had been making such a mess of the Dark Gray 9N paint that Ford wanted a new color for the 8N that would not contrast as much. Yuck, thankfully I have not found any official reference to 'Sparrow Poop Gray Paint' ever being an official Ford color. Some say the red was to make rust less noticeable. That rumour seems like something that might have been created by the John Deere club.

Trying to match original colors is difficult. Modern paints are very different, and perform much better than the original paint. Nothing you buy today will appear EXACTLY the same as the original finish under all types of lighting, and it certainly won't age the same. What looks right in your garage might not look right in the sun. Camera and monitor settings vary so much I often get different looking colors in photos of the same tractor, taken under the same lights, a few minutes apart. Not surprisingly, there is a lot of disagreement between the various experts about the best match for original colors. Some have their paint custom-mixed to match the color on a part that has been protected from sun and weather. I put very little faith in the theory that paint on the back side of a part has not changed color in 50 years or more. Even hidden from sunlight, old paint has been exposed to temperature changes, humidity, fuel vapors, oil, .. We could go to the local New Holland dealer to buy 'original color' paint. By all accounts the Ford Red sold by New Holland dealers is too orange for the 8N tractors. It may be correct for the '01 series tractors that started around 1957. The New Holland 'Ford Blue' is certainly not the same color used on the older Ford tractors. I prefer to use readily available standard paint colors that come reasonablt close. There are more than enough colors available. In some cases there are 'Farm and Implement' colors that may be closer than anything else off the shelf.

Ford Tractor Colors:

Ford 30008N-Red8N-Gray9N/2N
Krylon Ford Tractor Blue 1936Rust-Oleum - 7762 Sunrise RedRust-Oleum Mix - 7786+7770Rust-Oleum - 7786 Smoke Gray
PPG/Ditzler: 12908PPG/Ditzler: 70205PPG/Ditzler: 30448PPG/Ditzler:
Tisco: TP 360Tisco: TP 2822Tisco: TP 245Tisco: TP 2888
Van Sickle Ford Blue 466Van Sickle Ford Red 480Van Sickle Ford Gray 457Van Sickle Ford Dark Gray 475
Sherwin Williams: J5-1837

The first row of color swatches above is the RGB color codes taken from various published Ford color code charts. The second row of colors is the RGB codes for the colors I use. This is only intended to show how close I can get to the 'real' colors using off the shelf paint. The colors I choose are generally slightly lighter in color because the original paint very quickly faded to a lighter color. I feel choosing the lighter shade is closer to what a fairly new working tractor would look like in the wild. Different computer screens show the same colors differently. Even the same screen with slightly different adjustments will not show the same colors. So comparing 'live' colors to anything on a computer screen is mostly a waste of time. My color swatches in the chart above were created by going to various manufacturers web sites and getting the internet color codes they use for their swatches. I believe the manufacturers spend a lot of time choosing internet color codes that should look closest to the real colors. I believe this is the best way to compare paint colors on-line, even when the colors may not display correctly. If the color I want is a little less bright, or a little less blue than a known color, I can compare manufacturers RGB color codes to find something that should look better. This method has been worked well for me, but I still test colors by getting one rattle can, or a pint to see the real color on real parts.

My 52-8N Colors:

I decided to stick with what I know and use Rust-Oleum 'Stops Rust' paint. I have had good performance in the past with this brand and their useless rattle cans do not affect how the quarts spray and perform. Rust-Oleum used to have a color 7755 Light Olive, that I believe was very close to the correct Ford Light Gray, but it was not available anywhere in this area. They used to list the color on their web site, but it is no longer even listed. For the 52, I decided to get a quart of Rust-Oleum 7786 Smoke Gray, and mix it 50:50 with a quart of 7792 Gloss White. The color I ended up with was a little too light, but since the correct color tends to fade to white, it was not a bad choice. The idea was to find an easy mix that would be easy to repeat for touch-up or replaced parts.

Grey Paint Brush

My 46-2N Colors:

Grey Paint Brush

After all that, the 46-2N should have been easy, simple, dark gray, right? Nope, that would be too easy. I decided to go with the 8N paint scheme. This time, for the light gray, I used a quart of Rust-Oleum 7786 Smoke Gray, mixed 50:50 with a quart of 7770 Almond. The color I ended up with lookes better, and is still very easy to find and make again.


The following table has all the information I could find regarding original colors of various parts. This table is good for the vast majority of these tractors. HOWEVER, The earliest 9N tractors were very different from most other 9N tractors. There was more chrome on the very early tractors (radiator cap, gauge bezels, choke knob). The early 9Ns also used a four spoke Ford truck steering wheel with a chrome hub cap. Later tractors used a 3 spoke steering wheel with an exposed chrome washer and nut.

Air CleanerRedDark Gray
Axle HousingsRedDark Gray
Axle HubsRedDark Gray
Battery CableBlack InsulationBlack Insulation
Battery CoverRed with DecalNA
Battery TrayRedDark Gray
Battery/Fuel Door KnobBlackChrome
Battery/Fuel DoorLt GrayDark Gray
Brake DrumsRedDark Gray
Brake PedalsRedDark Gray
Breather CapRedDark Gray
Cable Terminals and HardwareUnpaintedUnpainted
CarburetorRed or UnfinishedUnfinished
Choke KnobUnpainted Metal or BlackUnpainted Metal or Black
Clutch PedalRedDark Gray
Cylinder HeadRedDark Gray
Dash PanelRedDark Gray
Distributor CapUnfinishedUnfinished
Drag LinkRedDark Gray
DrawbarRedDark Gray
Engine BlockRedDark Gray
Fan BeltBlack RubberBlack Rubber
Fan ShroudRedDark Gray
FanRedDark Gray
Fender BracketsLt GrayDark Gray
Fender Mounting BoltsCad PlatedCad Plated
FendersLt GrayDark Gray
Ford EmblemRed with Chrome Script and BorderBlue with Chrome Script and Border
Front Axle ExtensionRedDark Gray
Front HubsRedDark Gray
Front RimsLt GrayDark Gray
Front Timing CoverRedDark Gray
Fuel LineUnpainted-SteelUnpainted-Steel
Fuel TankCadmium-PlatedCadmium-Plated
Gearshift BootBlack RubberBlack Rubber
Gearshift KnobRed 1-Piece (early) Black Plastic (later)Dark Gray
GearshiftRedDark Gray
GeneratorRedDark Gray
GrillLt GrayDark Gray
Ground StrapUnpaintedUnpainted
Guage FacesBlack-White LettersBlack-White Letters
Guage TrimBlackBlack
Headlight HousingsLt Gray - Plated ScrewsDark Gray - Plated Screws
Hood Side SkirtsLt GrayDark Gray
HoodLt GrayDark Gray
Ignition SwitchUnpaintedUnpainted
Light SwitchUnpaintedUnpainted
Lug NutsZinc PlatedZinc Plated
Muffler and PipeZinc PlatedZinc Plated
Oil Filter BoltZinc PlatedZinc Plated
Oil Filter HousingRed Dark Gray
Oil PanRedDark Gray
Position Control LeverRedNA
Proofmeter FaceBlack-White LettersNA
Proofmeter TrimBlackNA
PTO KnobRed or PlainDark Gray
PTO LeverRed Dark Gray
PTO Shaft CoverRedDark Gray
Radiator CapBlackChrome?
Radiator HoseBlack RubberBlack Rubber
Radius RodsRedDark Gray
Rear End HousingRed Dark Gray
Rear RimsZinc PlatedZinc Plated
Rear Wheel CentersLt GrayDark Gray
Running BoardsRedDark Gray or None
Seat & SpringBlackDark Gray
Spark Plug Wire TubeCadmium-PlatedCadmium-Plated
Spark Plug WiresUnpainted-BlackUnpainted-Black
Spark PlugsUnpaintedUnpainted
Starter ButtonUnpainted-SteelUnpainted-Steel
StarterRedDark Gray
Steering Wheel NutPlated Acorn NutPlated Acorn Nut
Three-Point Hitch ArmsRedDark Gray
Throttle Lever BaseCadmium-PlatedCadmium-Plated
Throttle LeverCadmium-PlatedCadmium-Plated
Tie RodsRedDark Gray
Timing Cover BoltsZinc PlatedDark Gray
ToolboxRedDark Gray
Touch Control LeverRed Dark Gray
Transmission HousingRed Dark Gray
Valve CoversRedDark Gray
Wire HarnessUnpaintedUnpainted

After painting, the hardware used to attach sheet metal and other parts during final assembly was generally just standard Cad-Plated hardware.

The Manifold is shown as UNKNOWN in the table because they may have been plain castings or painted. I have not been able to nail this down. It is almost meaningless anyway. Even if they were painted, the paint soon burns off the exhaust portion of the manifold. If you don't like rusty cast iron, the best product I have found is a high temp natural cast iron coating for manifolds sold by Eastwood. Every other hi-temp coating I have tried fails as soon as I get the exhaust good and hot. Idling around won't get the exhaust that hot, so your trailer queen's exhaust might look nice longer. Putting a load on the engine for more than 20 minutes will cook off most hi-temp finishes. Even chrome plating tends to turn blue. Ceramic coatings are supposed to be able to withstand the heat, but the price is way beyond what I'm willing to spend to test that theory.

In general all hardware holding the major castings together was painted when the assembly was painted. The next photo is sort of what the 8N tractors looked like on the assembly line when they were painted.

This is as far as I go unless the tractor needs to be split to replace the clutch or fix something else major. If that is necessary, I wait to prime and paint the tractor after I have it back to this point again. Some restorers prime and paint each casting separately. Then paint again, after the major parts are assembled to cover scratches and hardware. I don't know if going that far on a tractor has any real value, but the guys who do go to that level turn out some incredibly nice tractors, like this one:

Restored Tractor by Derek Barkley at

all about paintbrush care

Learn how to clean a paintbrush properly, to ensure that your paintbrush has a long lifespan!

The sign of a happy paintbrush is one that is gooped in paint, dripping with color, and skipping freely across a canvas - gleefully leaving behind a trail of peppy pigment. A happy paintbrush is a faithful sidekick and as such, deserves to be well-treated. It's important to take good care of your paintbrushes, so that you can enjoy one another's company for a long time to come!

Gray Rustoleum Colors

So to keep your paintbrushes happy, remember these few points:

How to Clean a Paintbrush & Keep it Happy

The most important thing to remember in terms of brush care when working with acrylics is that acrylic paint dries very quickly. Always keep your brush wet or moist. Whatever you do - don't let the paint dry on the brush! The longer it is allowed to dry on the brush, the harder the paint will become, which makes it more difficult (if not downright impossible) to remove. Dried acrylic paint on a brush basically ruins the brush, effectively turning it into a crusty stump. Even if you know how to clean a paintbrush, there's really no way to de-crustify a crusty stump of a paintbrush.

What happens if you do happen to let acrylic dry on your paintbrush? Is all hope for the brush lost? Not so, read here to find out what you can do with crusty brushes!

Because acrylics dry so quickly and I want to avoid letting the paint dry on the brush, I typically work by using one brush at a time. On those rare moments when I do use more than one, I keep a close eye on the ones that are not in use, occasionally dipping them in water and shaking off the excess, just to keep them moist. When I'm not using them, I rest them across the rim of my cup of water. As soon as I think I'm done using one of the brushes, I'll thoroughly clean it before continuing with the painting.

Let's refresh our knowledge of the basic parts of a paintbrush:

You see that silvery bit that connects the hairs of the brush with the handle? That part of the brush is called the ferrule. In general, try not to get paint on the ferrule. When paint gets on the ferrule, it's usually connected in a large blob between the ferrule and the hairs, and the result (even after you wash it) is that the hairs will spread apart and wind up frayed. So try your best not to get paint on this part of the brush!

3. Don't rest your paintbrush with bristles down in a cup of water

This is another important point - never leave your brush with the hairs down in a cup of water - not even for a few minutes. This will cause the hairs to bend and/or fray and go all wonky, and the effect is irreversible. If your brushes are precious to you, then this is a definite no-no. Even if the hairs don't bend, for example if it's a rather stiff brush, the hairs will still spread in the water and become frayed and puffed when dry. It will basically never be the same paintbrush ever again!

If you make a purchase via the links below I receive a small commission, which helps support this site.

When actively using more than one paintbrush at a time, it is best to place the brushes that are on 'stand-by' in such a way that the bristles are not touching your palette or tabletop, especially if there is paint on the brush. One easy solution is to lay them horizontally with the bristles hanging over the edge of your work table. This is what I do when I'm working in a place where the floor is either protected or allowed to get paint stains. A more posh solution is this Porcelain Brush Holder. You can rest the paintbrushes in the grooves, keeping the bristles raised. The brush holder is heavy enough that it won't slide around or easily fall over.

Here's another solution for keeping your paintbrushes upright and easily accessible whilst painting. It also serves as a safe solution for transporting your beloved paintbrushes! The Alvin Prestige Paintbrush Holder is made from sturdy black nylon with a handy velcro enclosure.

This brush holder folds up to protect your brushes during transport, and when you're ready to paint, simply pull the drawstring elastic to prop the holder upright, making your paintbrushes easy to reach. The Alvin Prestige Paintbrush Holder is available in two sizes.

Sometimes the unexpected happens. If there's a sudden emergency or interruption (the phone ringing, for example) and you need to dash off in a rush, try to take the extra 10 seconds to do this:

Quickly swish your paintbrush in water, then squeeze out the excess paint and water in a paper towel or rag. Then quickly swish it again in the water and leave it gently resting across the rim of your water cup.

This simple procedure can be done in under 10 seconds. This way, if you're gone for awhile, the brush will stand a better chance of being saved. Leaving it hairs-down in a container of water will surely ruin it, so why take the chance?

Of course, use common sense though. For example, if your studio is on fire, save yourself. You can always buy new brushes! That's an extreme example, but you know what I mean.

So what happens if you do wind up with a crusty stump instead of a paintbrush? To look at the positive side, you don't necessarily have to throw it away. Perhaps out of a deep sense of loyalty, I always have difficulty throwing brushes away after they've become crusty or frayed. So I keep them, and use them as 'alternative' art-making tools. Even if the bristles of the brush become hard and brittle, they can still be used to apply paint onto a canvas, albeit in a more rough, expressionistic way. This makes them great for painting abstract art or other styles of artwork that don't require intricate precision or gentle brushstrokes. You can also use the handle of the brush to scrape designs into a thick layer of paint on the canvas.

Grey Paint Brush

Be aware that the hairs of your brush may (and will, eventually) get tinted to whatever color you've been using. This is normal and nothing to worry about. The stained color is locked into the bristles, so the color won't stain or intermix with your paint the next time you use it. Don't worry, if your brush gets tinted with color, it's not ruined!

Caring for your paintbrush is mainly a matter of common sense. If you treasure your tools, you'll intuitively know how to treat them. Just follow these guidelines and you will have a set of happy paintbrushes on your hands!

Now, find out how to clean a paintbrush!

Art is Fun Paintbrush Guide

Page 1.... describes the different types of brushes for acrylics and what each paintbrush can do.

Page 2.... answers all the questions that a beginning artist will have about paintbrushes.

Page 3.... explains how to safely care for your paintbrushes and keep them happy.

Page 4.... demonstrates the best way to clean, store and transport your paintbrushes.

Grey Neopets

read more..

Grey Paint Brush Neopets

Click here to return to the main Acrylic Table of Contents page, where you will find links to all of the acrylic information and tutorials on this site!